Author Topic: Bob's servo kit  (Read 167 times)

Dr.cgad

  • Jr. Member
  • **
  • Posts: 66
    • View Profile
    • Email
Bob's servo kit
« on: August 24, 2017, 07:30:41 AM »
If i do well for the first 9 weeks of school, my mother agreed to order bob's servo kit. Before anyone asks, i'm 14. Anyway can i get info on everything bob did to save steps when building it like say pre drilled holes.
Try not to get sucked into the vortex of hell Billy!

Danzilla93

  • Full Member
  • ***
  • Posts: 112
    • View Profile
    • Email
Re: Bob's servo kit
« Reply #1 on: August 24, 2017, 08:29:30 AM »
Let's see...

If my memory recalls correctly:

-The foam insulation is already attached to the hoverskirt
-The Hoverskirt is white plastic - no painting required
-The Tyco trains are black plastic - no painting required
-Bolts are already inserted into the upper arms (and come with nuts)
-Bolts are already inserted into the engine block (and come with nuts)
-Holes for the engine block are already drilled into the barrel
-The bottom of the barrel is already cut out
-A hole has been cut in the top of the barrel for the PVC control rod
-The shoulders are white plastic - no painting required
-The T Connecter has been cut down to shape to fit inside the head
-The upper arms and hands are already white, but painting them is still recommended as resin will yellow over time

I think that's all the time saving stuff Bob included in the kit!  I hope this helps!  Good luck on your build!  ;D

DentonUSA

  • Jr. Member
  • **
  • Posts: 72
  • "Knew your father,I did!"
    • View Profile
    • Email
Re: Bob's servo kit
« Reply #2 on: August 24, 2017, 03:53:51 PM »
I purchased Bob's kit, but there was no bolts attached to the arms or engine block. There were no pre-drilled holes for the arms or engine block, but there are markings to show where to drill. I don't know if that was just mine, but be prepared just in case. Hope I helped!

Dr.cgad

  • Jr. Member
  • **
  • Posts: 66
    • View Profile
    • Email
Re: Bob's servo kit
« Reply #3 on: August 24, 2017, 08:43:58 PM »
Let's see...

If my memory recalls correctly:

-The foam insulation is already attached to the hoverskirt
-The Hoverskirt is white plastic - no painting required
-The Tyco trains are black plastic - no painting required
-Bolts are already inserted into the upper arms (and come with nuts)
-Bolts are already inserted into the engine block (and come with nuts)
-Holes for the engine block are already drilled into the barrel
-The bottom of the barrel is already cut out
-A hole has been cut in the top of the barrel for the PVC control rod
-The shoulders are white plastic - no painting required
-The T Connecter has been cut down to shape to fit inside the head
-The upper arms and hands are already white, but painting them is still recommended as resin will yellow over time

I think that's all the time saving stuff Bob included in the kit!  I hope this helps!  Good luck on your build!  ;D
thanks i'm about to pass week 3 then 6 to go.
Try not to get sucked into the vortex of hell Billy!

Dr.cgad

  • Jr. Member
  • **
  • Posts: 66
    • View Profile
    • Email
Re: Bob's servo kit
« Reply #4 on: September 02, 2017, 05:10:29 PM »
4 down 5 to go
Try not to get sucked into the vortex of hell Billy!

Dr.cgad

  • Jr. Member
  • **
  • Posts: 66
    • View Profile
    • Email
Re: Bob's servo kit
« Reply #5 on: September 20, 2017, 07:52:29 PM »
2.5 weeks to go
Try not to get sucked into the vortex of hell Billy!